水菜丽加勒比av在线播放-国产精品一区二区三区综合-国产精品一区二区久久不-欧美国产精品亚洲精品观看

當前位置:首頁-新聞中心新聞中心

通風管道加工的要遵守的細節制作

發布人:http://m.hwzxw.net   發布時間:2018-04-19 16:02:29

1、 在一道密閉閥門工程口部的管道與配件,應采用厚2-3mm的鋼板焊接制作,其焊縫應飽滿、均勻、嚴密。

1. The piping and fittings of the first closed valve to the engineering port should be welded by thick 2-3mm steel plate. The welds should be full, even and tight.

2、染毒區的通風管道應采用焊接連接。通風管道與密閉閥門應采用帶密閉槽的法蘭連接,其接觸應平整;法蘭墊圈應采用整圈無接口橡膠密封圈。

2, the ventilation pipeline in the contaminated area should be welded. Ventilation pipes and closed valves shall be connected with flanges with closed grooves, and the contact shall be smooth; the flange gaskets shall be provided with a whole ring without interface rubber seals.

3、 主體工程內通風管與配件的鋼板厚度應符合設計要求。當設計無具體要求時,鋼板厚度應大于0.75mm。

3. The thickness of the steel plate of the ventilation pipe and fittings in the main project should meet the design requirements. When there is no specific requirement for design, the thickness of the steel plate should be greater than 0.75mm.

20170427020431145.jpg

4、工程測壓管在防護密閉門外的一端應設有往下的彎頭,另一端宜設在通風機房或控制室,并應安裝球閥。通過防毒通道的測壓管,其接口應采用焊接。

4. One end of the engineering piezometric tube should be provided with a downward elbow at the end of the closed door, and the other end should be installed in the ventilator room or control room, and the ball valve should be installed. The interface should be welded through the pressure measuring pipe of the anti-virus passageway.

5、通風管的測定孔、洗消取樣管應與管同時制作。測定孔和洗消取樣管應封堵。

5. The measuring hole and cleaning sampling tube of the ventilating pipe should be made at the same time with the tube. The test hole and the washing tube should be blocked.

6、 通風管內氣流方向、閥門啟閉方向及開啟度,應標示清晰、準確。

6. Airflow direction, opening and closing direction and opening degree of the ventilation pipe should be clearly marked and accurate.

7.材料表面油污應全部干凈,以免鐵銹或氧化物落于材料表面產生局部腐蝕。

7. the oil on the surface of the material should be cleaned up so as to avoid rust or oxide falling on the surface of the material to cause localized corrosion.

8.必須有一個單獨的加工場地,為了不破壞鍍鋅鋼板外的保護膜,工作場地較好鋪設木板或者橡膠板,保持場地清潔。

8. it is necessary to have a separate processing site. In order not to destroy the protective film outside the galvanized steel sheet, the best work site is to lay a wood board or rubber plate to keep the site clean.


上一篇:通風管道特點及安裝事項
下一篇:降低通風機聲源噪聲有哪些方法?

網站首頁 關于我們 產品展示 新聞中心 工程案例 在線留言 聯系我們

巴中市| 纳雍县| 海林市| 收藏| 鞍山市| 绍兴市| 萝北县| 青田县| 洛宁县| 大名县| 同德县| 平乐县| 溧阳市| 紫阳县| 内黄县| 贺兰县| 阜宁县| 兴业县| 辽中县| 来凤县| 宜君县| 建昌县| 宁都县| 漯河市| 沙坪坝区| 昌吉市| 嘉善县| 杭州市| 太湖县| 卢湾区| 永康市| 宜丰县| 哈尔滨市| 凤阳县| 长海县| 扶风县| 合江县| 巨野县| 镇沅| 改则县| 广丰县|