山東通風管道:黑鐵皮與白鐵皮

發布人：http://m.hwzxw.net   發布時間：2019-06-04 16:33:38

　　山東通風管道板材:黑鐵皮與白鐵皮

　　Shandong Ventilation Pipeline Plate: Black Iron and White Iron暖通空調系統主要包括通風工程和空調工程兩大局部。通風工程普通包括送風和排氣、除塵和工程?？照{(diào)工程普通包括空調、恒溫恒濕和空氣凈化工程。

　　HVAC system mainly includes two parts: ventilation engineering and air conditioning engineering. Ventilation engineering generally includes air supply and exhaust, dust removal and detoxification engineering. Air conditioning engineering generally includes air conditioning, constant temperature and humidity and air purification engineering.

　　通風工程與空調空調系統需求經過風道銜接，完成2F黑鐵皮普通酸洗鋼板(黑鐵皮)的設計功用:由碳鋼經熱軋或冷軋制成。熱軋鋼過程的,由于很容易突破和空調用于冷軋,模型普通有Q195、Q215 Q235,有兩品種型的表和線圈,常用的厚度為0.5 ~ 2毫米,黑色板近年來在暖通空調工程運用純黑色單少,黑鐵和錫的區別不是黑鋼板外表處置,容易氧化和生銹。

　　Ventilation works and air conditioning systems need to be connected through air ducts to complete the design function of 2F black iron sheet common pickling steel sheet (black iron sheet): made of carbon steel by hot or cold rolling. Hot rolled steel process, because it is easy to break through and air conditioning is used for cold rolling, the model generally has Q195, Q215 Q235, there are two types of surface and coil, the commonly used thickness is 0.5-2 mm, black sheet in recent years in HVAC engineering using pure black sheet, black iron and tin is not the difference between the surface treatment of black steel plate, easy oxidation and rust.

　　錫

　　tin

　　鍍鋅鋼板(鐵皮):由鍍鋅黑鐵皮制成，俗稱鐵皮。常用厚度0.5~1.5mm，規格尺寸與普通薄鋼板(黑鐵皮)相同。鍍鋅層厚度不小于0.02mm。鍍鋅鐵的優點:外表具有防腐作用，所以普通不需求刷油防腐，普通用于保送酸霧作用的濕潤環境通風系統和空調系統及配件。

　　Galvanized steel sheet (iron sheet): Made of galvanized black iron sheet, commonly known as iron sheet. Commonly used thickness is 0.5-1.5 mm, the size is the same as that of ordinary thin steel plate (black iron sheet). The thickness of galvanized layer is not less than 0.02mm. Advantages of galvanized iron: The appearance has anti-corrosion effect, so it is not required to brush oil and anti-corrosion. It is commonly used for humid environment ventilation system and air-conditioning system and accessories to protect acid fog.

　　山東通風管道

　　Shandong Ventilation Pipeline

　　管道裝置的普通請求

　　General Request for Pipeline Devices

　　1)風管程度裝置，程度度允許偏向不大于3mm / m，總偏向不大于20mm;風管垂直裝置。垂直度允許偏向不大于2mm / m，總偏向不大于20mm。

　　1) Ventilation duct degree device, degree allowable deviation is not more than 3m m/m, total deviation is not more than 20mm; Ventilation duct vertical device. The allowable deviation of perpendicularity is not more than 2 m m/m and the total deviation is not more than 20 mm.

　　2)管道吊架與法蘭之間的間隔不得小于20mm。柔性短管長度150~300mm。金屬軟管和非金屬軟管長度不得大于2m，不得有死彎或垮落現象。

　　2) The distance between the pipe hanger and the flange shall not be less than 20 mm. The length of flexible short tube is 150-300 mm. The length of metal hose and non-metal hose shall not be greater than 2m, and there shall be no dead bending or collapse.

　　3)主氣管吊架與支管之間的間隔不得小于200mm。

　　3) The interval between the main pipe hanger and the branch pipe shall not be less than 200 mm.

　　4)法蘭螺栓與低壓送風孔距不大于200mm，中壓送風孔距不大于100mm。

　　4) The distance between flange bolt and low pressure air supply hole is not more than 200 mm, and that between medium pressure air supply hole is not more than 100 mm.

　　5)風管彎頭、三通、閥門處必需加吊鉤。管道長度應超越15m，防搖支架不得小于1根。

　　5) Hooks must be added at elbows, tees and valves of air ducts. Pipeline length should exceed 15m and anti-sway bracket should not be less than 1.

　　6)通風管道吊架間隔不保溫風管邊緣30mm，間隔保溫風管保溫層邊緣30mm。

　　6) The suspension rack of ventilation duct is separated by 30 mm of the edge of the insulating duct and 30 mm of the insulating layer of the insulating duct.

　　7)風管保溫應平整，法蘭必需單獨保溫，法蘭保溫資料應與管道分歧。風管程度度為3‰，垂直度為2‰，總偏向不超越20mm。

　　7) Air duct insulation should be flat, flange insulation must be separate, flange insulation data should be different from the pipeline. The degree of duct is 3, the vertical degree is 2 and the total deviation is not more than 20 mm.

　　8)風管與法蘭壓邊座寬度為6~9mm，嚴密、直觸。

　　8) The width of air duct and flange blank holder is 6-9 mm, which is close and direct contact.

　　9)玻璃鋼管道法蘭銜接時，法蘭螺栓間距不大于120mm，法蘭間距平均，法蘭應平整，法蘭墊片厚度為3~5mm。

　　9) When connecting the flanges of FRP pipelines, the spacing of flange bolts is not more than 120 mm, the spacing of flanges is average, the flanges should be flat, and the thickness of flange gaskets should be 3-5 mm.

　　10)玻璃纖維管道長度超越20m時，應增加不少于一個固定支架;玻璃纖維風管長度超越20m時，應按設計請求增加伸縮縫。

　　10) When the length of fiberglass duct exceeds 20m, not less than one fixed bracket shall be added; when the length of fiberglass duct exceeds 20m, the expansion joint shall be added according to the design request.

　　11)氣管經過的收縮節采用軟銜接。軟管長度為100mm +伸縮縫寬度。風管保溫資料為巖棉時，保溫采用鐵角打包帶，間距0.6~0.7m。通風管道規格400mm以下的支吊架間距不得大于4m，通風管道規格400mm以上的支吊架間距不得大于3m。

　　11) The contraction joints of trachea are connected by soft joint. The length of hose is 100mm + the width of expansion joint. When the data of air duct insulation is rock wool, iron angle packing belt is used for insulation, and the spacing is 0.6-0.7m. The spacing between supports and hangers with ventilation pipe specifications of less than 400 mm shall not be greater than 4 m, and that between supports and hangers with ventilation pipe specifications of more than 400 mm shall not be greater than 3 m.

　　13)風管垂直裝置，支架間距不大于4m，玻璃管不大于3m。

　　13) Ventilation pipe vertical device, bracket spacing is not more than 4m, glass tube is not more than 3m.

　　14)排氣管與屋面風機銜接采用6mm橡膠墊，鍍鋅螺栓加平墊、彈簧墊圈。

　　14) The exhaust pipe and the roof fan are connected by 6mm rubber pad, galvanized bolt with flat pad and spring washer.

　　15)室外鐵管保溫應平整、潤滑，咬合不小于20~25mm。

　　15) Outdoor iron pipe insulation should be smooth and lubricated, and the occlusion should not be less than 20-25 mm.