通風管道清理小妙招都有哪些?
發布人:http://m.hwzxw.net 發布時間:2020-01-08 11:43:42
隨著使用時間的不斷增長,通風管道會積累大量的雜質。這些雜質會在管道中停留很長時間,在操作過程中會加速油的凝結。溫度轉換過高,會對氣動閥、液壓元件造成損壞,對正常運行有很大影響。因此,有必要定期清理通風管道設備。
With the continuous growth of use time, a large number of impurities will accumulate in the ventilation pipe. These impurities will stay in the pipeline for a long time and accelerate the oil condensation during operation. Too high temperature conversion will damage the pneumatic valve and hydraulic components, and have a great impact on normal operation. Therefore, it is necessary to clean the ventilation pipe equipment regularly.
(1)風道與風機連接時,進、出口應安裝軟接頭。軟接頭的截面尺寸應與風機進出口截面相同。軟管連接可以由帆布、人造皮革和其他材料制成。軟管長度不應小于200,并應適當擰緊。軟管可以緩沖風扇的振動。
(1) When the air duct is connected with the fan, soft joints shall be installed at the inlet and outlet. The section size of the soft joint shall be the same as that of the fan inlet and outlet. Hose connections can be made of canvas, artificial leather, and other materials. The hose length shall not be less than 200 and shall be properly tightened. The hose dampens the vibration of the fan.
(2)風管與除塵設備、加熱設備連接后,根據理論映射安裝好設備后,停止預制安裝。
(2) After the air duct is connected with the dedusting equipment and heating equipment, the prefabricated installation shall be stopped after the equipment is installed according to the theoretical mapping.
(4)輸送凝結水或高含水率氣體時,水平管道應設置在斜坡處,并與下部排水管連接。安裝時風道底部不應有縱向接縫,底部接縫應懸掛密封。
(4) When transporting condensate or high moisture content gas, the horizontal pipeline shall be set at the slope and connected with the lower drainage pipe. There shall be no longitudinal joint at the bottom of air duct during installation, and the bottom joint shall be hung and sealed.
(5)輸送易燃易爆氣體的鋼板風道,在風道連接法蘭處安裝跳線,并與靜電接地網連接。
(5) For the steel plate air duct conveying inflammable and explosive gas, install jumpers at the connecting flange of the air duct and connect with the electrostatic grounding grid.
(6)水平風道高度在4m以上時,安裝人員應系好帶。腳手架或活動支架上的舷梯應固定,舷梯寬度應符合規范,腳手架上的設備人員應隨身攜帶物品袋,避免物品或電鉆等掉落傷人。通風管道主要用于工業和建筑工程,設計領域廣泛。吸油、吸煙、除塵的工作環境,現在需要使用通風管道。使用天然空氣代替室內空氣,改善室內空氣質素。
(6) When the height of horizontal air duct is more than 4m, the installation personnel shall fasten the safety belt. The gangway on the scaffold or movable support shall be fixed, and the width of gangway shall conform to the safety specifications. The equipment personnel on the scaffold shall carry the bag with them to avoid personal injury caused by falling objects or electric drills. Ventilation pipe is mainly used in industry and construction engineering, and its design field is wide. The working environment for oil absorption, smoking and dust removal now requires the use of ventilation pipes. Use natural air instead of indoor air to improve indoor air quality.
通風管道的使用:
Use of ventilation ducts:
1. 凈化空調系統風道:鍍鋅板、不銹鋼;(嚴禁使用受塵源污染的FRP及復合材料)
1. Air duct of purification air conditioning system: galvanized sheet and stainless steel; (FRP and composite materials polluted by dust source are strictly prohibited)
2. 空調系統風道:鍍鋅板、彩鋼保溫板;(可使用玻璃纖維及復合材料)
2. Air duct of air conditioning system: galvanized board, color steel insulation board; (fiberglass and composite materials can be used)
3.環境控制系統風管:鍍鋅板、不銹鋼;(塑料、玻璃纖維、復合材料等)
3. Air duct of environmental control system: galvanized sheet, stainless steel; (plastic, glass fiber, composite material, etc.)
4. 工業通風系統風道:鋼板、鍍鋅板;(荔波通風管。塑料、玻璃纖維、復合材料等)
4. Air duct of industrial ventilation system: steel plate, galvanized plate; (Libo ventilation pipe. Plastic, glass fiber, composite materials, etc.)
5. 特殊場合風道:礦山用涂膠風道,礦山用塑料風道;要求具有阻燃、防靜電的礦井特性
5. Air duct for special occasions: rubber coated air duct for mine and plastic air duct for mine; it is required to have fire-retardant and anti-static mine safety characteristics
以上就是對濟南通風管道清理的小妙招的詳細介紹,想要了解更多請點擊官網http://m.hwzxw.net
The above is a detailed introduction to the tips of Jinan ventilation pipeline cleaning. To learn more, please click http://m.hwzxw.net性)
上一篇:市場對濟南通風管道潔凈度的需求都有哪些?
下一篇:黑白鐵加工流程都需要哪些技術?