水菜丽加勒比av在线播放-国产精品一区二区三区综合-国产精品一区二区久久不-欧美国产精品亚洲精品观看

當前位置:首頁-新聞中心新聞中心

如何測定通風管道內的風速及風量?

發布人:http://m.hwzxw.net   發布時間:2020-09-18 15:04:42

  通風管道內風速及風量的測定,是通過測量壓力換算得到的。下面由小編給大家介紹一下:

  The measurement of wind speed and air volume in ventilation duct is obtained by conversion of measured pressure. Now let's introduce it to you:

  據了解,要想測得管道中氣體的真實壓力值,除了正確使用測壓儀器外,合理選擇測量斷面、減少氣流的擾動對測量結果的影響很大。

  It is understood that in order to measure the real pressure value of the gas in the pipeline, in addition to the correct use of pressure measuring instruments, reasonable selection of measurement section and reduction of airflow disturbance have great influence on the measurement results.

  測量斷面應盡量選擇在氣流平穩的直管段上。測定動壓時如發現任何一個測點出現零值或負值,表明氣流不穩定,該斷面不宜作為測定斷面。

  The measurement section should be selected on the straight pipe section with stable air flow as far as possible. If zero value or negative value is found at any measuring point during the measurement of dynamic pressure, it indicates that the air flow is unstable, and this section should not be used as the measurement section.

                                    QQ截圖20170428145504.png

  當測量斷面設在彎頭、三通等異形部件前面(相對氣流流動方向)時,距這些部件的距離應大于2倍管道直徑。

  When the measuring section is set in front of the elbow, tee and other special-shaped parts (relative to the flow direction of air flow), the distance from these parts should be greater than twice the pipe diameter.

  當測量斷面設在彎頭、三通等異形部件后面時,距這些部件的距離應大于4~5倍管道直徑。

  When the measuring section is set behind the elbow, tee and other special-shaped parts, the distance from these parts should be greater than 4-5 times of the pipe diameter.

  當測試現場難于滿足要求時,為減少誤差可適當增加測點。但是,測量斷面位置距異形部件的較小距離少是管道直徑的1.5倍。

  When the test site is difficult to meet the requirements, in order to reduce the error, the measuring points can be appropriately increased. However, the smaller distance between the measuring section and the abnormal part is at least 1.5 times of the pipe diameter.


上一篇:通風管道加工應該注意的事項!
下一篇:黑白鐵加工主要都有哪些內容?

網站首頁 關于我們 產品展示 新聞中心 工程案例 在線留言 聯系我們

大安市| 衡南县| 兴业县| 邛崃市| 昌吉市| 阳曲县| 佳木斯市| 景谷| 文成县| 确山县| 海盐县| 龙井市| 和硕县| 贵定县| 罗田县| 泽州县| 东莞市| 三河市| 南部县| 锡林郭勒盟| 伊通| 新安县| 霍州市| 日照市| 长宁县| 正定县| 苏尼特右旗| 肥城市| 吉首市| 德州市| 揭西县| 汉源县| 阆中市| 荆州市| 东方市| 大埔县| 吉安县| 静海县| 巨鹿县| 岚皋县| 庆安县|