室外裝飾中黑白鐵加工的一些細節？

發布人：http://m.hwzxw.net   發布時間：2021-05-28 14:01:49

在室外裝修工程施工前，應在墻基的擋板上對黑白鐵加工墻的底座進行全 面檢查，并認真處理黑白鐵加工過程中存在的問題。室外裝飾中黑白鐵加工的一些細節有哪些？

Before the construction of outdoor decoration project, the base of black and white iron processing wall should be checked on the baffle of wall base, and the problems existing in the process of black and white iron processing should be seriously dealt with. What are some details of black and white iron processing in outdoor decoration?

工作的主要內容是挖掘和填充主體工程施工所形成的混凝土墻面，框架柱或器官柱，待切割部分應彈性化，小心切割，并采用一些砌筑平整。鑿成的產品是好的，深凹表面應該用水洗滌，然后在刷涂后用水泥砂漿涂抹，直到它與基材的外表面均勻地弄平。

The main content of the work is to excavate and fill the concrete wall, frame column or organ column formed by the construction of the main project. The part to be cut should be elastic, cut carefully, and use some masonry to level. The chiseled product is good. The deep concave surface should be washed with water, and then coated with cement mortar after brushing until it is even with the outer surface of the substrate.

門和窗口位置上的檢查端口由從頂部到底部彈出。垂直控制線的下框線是拉水平線。為了防止門窗傾斜，門窗不礙事，上下整齊，誤差過大。要求的情況是提前做出全 面修正。門窗框架與墻體之間的間隙應密集分層嵌入，特殊人員應作為一個過程仔細完成，基本項目驗收應按門窗子項進行設備。

The inspection port on the door and window position is ejected from the top to the bottom by the top layer. The bottom border of the vertical control line is the horizontal line. In order to prevent the doors and windows from tilting, the doors and windows are not in the way, the up and down are neat, and the error is too large. The requirement is to make a comprehensive correction in advance. The gap between the door and window frame and the wall should be embedded in dense layers, special personnel should complete it carefully as a process, and the basic project acceptance should be carried out according to the door and window sub items.

當在框架填充墻的墻壁上開始抹灰時，由于混凝土和粘土磚墻兩種不同的水平材料在吸水性和縮短性能上沒有差別，這部分會隨機產生石膏表面裂縫的質量容易在這一部分，灰的底層預涂有與灰相同的砂漿，并且過渡層施加到接頭上，并且在鏜孔縮短之后停止生銹操作。

When plastering is started on the wall of frame infilled wall, because there is no difference in water absorption and shortening performance between concrete and clay brick wall, this part will randomly produce the quality of gypsum surface cracks. In this part, the bottom layer of the ash is pre coated with the same mortar as the ash, and the transition layer is applied to the joint, And stop the rusting operation after the boring is shortened.