水菜丽加勒比av在线播放-国产精品一区二区三区综合-国产精品一区二区久久不-欧美国产精品亚洲精品观看

當前位置:首頁-新聞中心新聞中心

螺旋風管其長度等方面是要好于矩形風管

發(fā)布人:http://m.hwzxw.net   發(fā)布時間:2024-04-22 10:20:42

螺旋風管其長度等方面是要好于矩形風管:這是由于普通的螺旋風管,其正常長度是為3米到6米,而矩形風管其是為1米到1.5米,除此之外,螺旋風管的長度,還能夠依照具體需求來定做,從其它方面來看,螺旋風管中的連接點,是能夠很大程度上根絕的,由于其風管之間的連接,只用管接件,而矩形風管則需求雙法蘭體系。

The length of spiral air ducts is better than rectangular air ducts: this is because ordinary spiral air ducts have a normal length of 3 to 6 meters, while rectangular air ducts have a length of 1 to 1.5 meters. In addition, the length of spiral air ducts can be customized according to specific needs. From other aspects, the connection points in spiral air ducts can be largely isolated. Due to the connection between their air ducts, only pipe fittings are used, while rectangular air ducts require a double flange system.

1、通風管道加工的過程中應該盡量避免出現縱向接縫,但是一定不能出現橫向接縫。而且通風管道的咬口縫和四角的縫隙處,需要按照設計潔凈等級要求,然后還要采用密封膠將其堵嚴。另外通風管道板材的連接縫的密封面應該設在通風管道壁的正壓側。

20230923445793.jpg

1. During the processing of ventilation ducts, longitudinal joints should be avoided as much as possible, but transverse joints must not occur. Moreover, the bite seams and corners of the ventilation ducts need to be sealed tightly with sealant according to the design cleanliness level requirements. In addition, the sealing surface of the connection joint of the ventilation duct board should be set on the positive pressure side of the ventilation duct wall.

2、加工的時候,不能在通風管道內部設置加固框或者加固筋,因為這樣對于通風管道的質量會造成一定的影響。

2. During processing, reinforcement frames or bars should not be installed inside the ventilation ducts, as this will have a certain impact on the quality of the ventilation ducts.

3、通風管道加工不能采用S型插條和C型直角插條的連接方式,另外對于一些特殊的通風管道來說,還不能采用按扣式的咬口。

3. The connection method of S-shaped and C-shaped right angle inserts cannot be used for the processing of ventilation ducts. In addition, for some special ventilation ducts, a snap fit cannot be used.

4、通風管道制作完畢之后,還要用清洗液進行清洗,只有達到清洗標準之后,才可以及時封口。

4. After the production of the ventilation duct is completed, it needs to be cleaned with cleaning solution. Only after meeting the cleaning standards can it be sealed in a timely manner.

5、玻璃纖維復合板風管端口為切割面時,在裝配法蘭連接件前應將管端切口面用膠帶或膠液進行封堵,才能防止玻璃纖維外露和飛散

5. When the end of the fiberglass composite panel air duct is cut, the cut surface of the pipe end should be sealed with tape or adhesive solution before assembling the flange connector to prevent the exposure and scattering of the fiberglass

本文來自:濟南風管加工廠更多的內容請點擊:http://m.hwzxw.net我們將會為您提問的問題提供一個滿意的服務,歡迎您的來電!

This article is from Jinan Wind Pipe Processing Factory. For more information, please click: http://m.hwzxw.net We will provide satisfactory service for the questions you ask. Welcome to call us!

上一篇:工業(yè)通風系統(tǒng)中拱板風管的應用
下一篇:不銹鋼焊接風管過濾網的安裝與變形

網站首頁 關于我們 產品展示 新聞中心 工程案例 在線留言 聯系我們

永靖县| 神池县| 上林县| 郎溪县| 阳西县| 临漳县| 龙陵县| 福建省| 洛扎县| 苍山县| 长治县| 沁阳市| 尼勒克县| 安乡县| 东城区| 石城县| 大理市| 西青区| 克山县| 象山县| 上杭县| 许昌县| 太仆寺旗| 黔江区| 昭觉县| 揭东县| 吉水县| 郯城县| 穆棱市| 铁岭县| 崇文区| 会理县| 德化县| 徐水县| 游戏| 资阳市| 长垣县| 伊金霍洛旗| 六枝特区| 鄢陵县| 疏勒县|